Say youre taking 3 different oil based injectables 3x a week. Most people arent going to want to do 9 separate injections every week. How do you combine your injectables for minimum injections? Do you take the three and combine them in a vial according to your proportions? Do you use the same needle & syringe and attempt to draw the correct dosage from all three into the same syringe? Seems it would be easy to mess up the correct quantities. Draw each one separately and then backfill into a separate syringe that will be used for the single injection?
Beginner
Answers 3
I pull whatever I’m using into one syringe using a big needle so it pulls faster, then I put my smaller needle on warm it up and then inject it. I’ll fill the 3ml syringe completely up. Bota beng bota boom.
Use an 18g needle to draw all 3 compounds into one 3-6 ml syringe
Similar situation. It’s better to draw out from 3 separate vials than to use a blend, that way YOU can physically observe what’s going in the final Syringe. Personal example: 3 Separate 10ml vials: Test E 250 / Tren E 200 / Mast E 200Monday & Thursday Injections: 1.Grab a 3ml Needle/Syringe that will be the one you use for your IM injection. Unscrew the needle from syringe & leave in plastic. 2.Attach larger gauge needle (20g, 18g) to draw up liquid faster from each vial. You can use the same needle to draw from all 3 vials. 3.After you have sanitized each vial top, simply draw out what you need: Ex: *I need 125mg test, 100mg tren, 200 mast 125mg Test= 0.5ml 100mg Tren= 0.5ml 200mg Mast= 1ml*Total of 2ml in the 3ml syringe (After I draw up out one liquid, I always pull the plunger back just slightly before drawing from the next vial to avoid suction from the second vial (in case the air-oil ratio isn’t equal in the vial.) This is for peace of mind and you can make sure what’s in your syringe (I.e. Test being sucked in to the Tren bottle) stays out of the next vial.4. When all oils are in one syringe, unscrew the larger needle you just used and reapply the unused needle you’re going to use for IM injection. Push and pull on the plunger some to remove any visible air or bubbles out of the syringe (if you look closely, you can see any tiny bubbles rising towards the top; they will eventually push themselves out). I then lay the syringe on a flat surface on its side and it will disperse the oils evenly (you will also be able to tell if there are any residual air bubbles).5. Clean your injection site w/ alcohol prep, insert needle @ 90* angle and push oils in slowly so it disperses evenly into the muscle.6.Once all the oil is out of the syringe, withdraw the needle in the same direction you inserted it, then grab an alcohol prep, cover the site and I would rub it for a good 30-60 seconds to keep oil from clumping in one spot, which will cause pain (PIP) down the road. Cover it with a band aid if necessary, and you’re set!Be safe & don’t rush
I pull whatever I’m using into one syringe using a big needle so it pulls faster, then I put my smaller needle on warm it up and then inject it. I’ll fill the 3ml syringe completely up. Bota beng bota boom.
Similar situation. It’s better to draw out from 3 separate vials than to use a blend, that way YOU can physically observe what’s going in the final Syringe. Personal example: 3 Separate 10ml vials: Test E 250 / Tren E 200 / Mast E 200Monday & Thursday Injections: 1.Grab a 3ml Needle/Syringe that will be the one you use for your IM injection. Unscrew the needle from syringe & leave in plastic. 2.Attach larger gauge needle (20g, 18g) to draw up liquid faster from each vial. You can use the same needle to draw from all 3 vials. 3.After you have sanitized each vial top, simply draw out what you need: Ex: *I need 125mg test, 100mg tren, 200 mast 125mg Test= 0.5ml 100mg Tren= 0.5ml 200mg Mast= 1ml*Total of 2ml in the 3ml syringe (After I draw up out one liquid, I always pull the plunger back just slightly before drawing from the next vial to avoid suction from the second vial (in case the air-oil ratio isn’t equal in the vial.) This is for peace of mind and you can make sure what’s in your syringe (I.e. Test being sucked in to the Tren bottle) stays out of the next vial.4. When all oils are in one syringe, unscrew the larger needle you just used and reapply the unused needle you’re going to use for IM injection. Push and pull on the plunger some to remove any visible air or bubbles out of the syringe (if you look closely, you can see any tiny bubbles rising towards the top; they will eventually push themselves out). I then lay the syringe on a flat surface on its side and it will disperse the oils evenly (you will also be able to tell if there are any residual air bubbles).5. Clean your injection site w/ alcohol prep, insert needle @ 90* angle and push oils in slowly so it disperses evenly into the muscle.6.Once all the oil is out of the syringe, withdraw the needle in the same direction you inserted it, then grab an alcohol prep, cover the site and I would rub it for a good 30-60 seconds to keep oil from clumping in one spot, which will cause pain (PIP) down the road. Cover it with a band aid if necessary, and you’re set!Be safe & don’t rush
Use an 18g needle to draw all 3 compounds into one 3-6 ml syringe